Clutch basket bearings

Posted: Sun Aug 19, 2018 8:04 pm

Where are you guys sourcing the bearings (2) that are inside the gear in the back side of the clutch? Part number 91010-300-008.
Here's a link for the part. Would like to have a known high quality bearing.
https://www.partzilla.com/product/honda/91010-300-008

CB1100F Joined: Jun 18, 2006 Posts: 2528 Location: UK

Hi Nathan

I think you need a HK2520 as your link shows 25 x 32 x 20

http://www.skf.com/group/products/bearings-units-housings/roller-bearings/needle-roller-bearings/drawn-cup-needle-roller-bearings/drawn-cup-pt/index.html?designation=HK%202520

I changed some in one of my baskets which were HK2516 25 X 32 X 16 as some baskets have narrower bearings fitted

Keith

Posted: Sun Aug 19, 2018 9:24 pm

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

Posted: Mon Aug 20, 2018 4:42 am

Testr wrote:

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

They should just slide in/out with very very little effort...they literally should fall out if you turned the basket on it's side.

CB1100F Joined: Jun 18, 2006 Posts: 2528 Location: UK

Shawn_Mc wrote:

Testr wrote:

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

They should just slide in/out with very very little effort...they literally should fall out if you turned the basket on it's side.

The one I did with narrow bearings had a wire circlip holding the bearings in

Hawk Joined: Jun 05, 2017 Posts: 330 Location: New England

Believe it or not, I ordered them from Amazon.

Posted: Wed Aug 22, 2018 12:20 am

Ordered a couple NTN bearings for this off Amazon today. We'll see how they are.

Posted: Wed Aug 22, 2018 12:56 am

Let me know would you please.

Posted: Wed Aug 22, 2018 2:45 am

Hondo57 wrote:

Let me know would you please.

I told Nich for you already Laughing

Posted: Wed Aug 22, 2018 3:27 am

nathanhouse wrote:

Hondo57 wrote:

Let me know would you please.

I told Nich for you already Laughing

Haha except I don’t order parts for Greg. He orders his own and they show up at my door!

I’ll glady pass it on though Smile

Posted: Wed Aug 22, 2018 11:01 am

I am still tryng to decide on the best clutch disc and plate setup. Everything else is ready to go

Posted: Wed Aug 22, 2018 9:51 pm

krgood0 wrote:

Shawn_Mc wrote:

Testr wrote:

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

They should just slide in/out with very very little effort...they literally should fall out if you turned the basket on it's side.

The one I did with narrow bearings had a wire circlip holding the bearings in

Thanks. I checked out mine which has the wider bearings so there was no circlip. They're in there pretty tight - certainly not 'fall out' loose. No problem, a little heat and a press will do it.

Posted: Thu Aug 23, 2018 12:32 am

Testr wrote:

krgood0 wrote:

Shawn_Mc wrote:

Testr wrote:

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

They should just slide in/out with very very little effort...they literally should fall out if you turned the basket on it's side.

The one I did with narrow bearings had a wire circlip holding the bearings in

Thanks. I checked out mine which has the wider bearings so there was no circlip. They're in there pretty tight - certainly not 'fall out' loose. No problem, a little heat and a press will do it.

Came right out with a press and the proper sized tool to push. I didn't use heat.

Posted: Sat Aug 25, 2018 4:05 pm

Sorry guys, I was thinking about the 900 clutch Embarassed

Posted: Sun Aug 26, 2018 10:07 am

Shawn_Mc wrote:

Sorry guys, I was thinking about the 900 clutch Embarassed

Mine is a 900 clutch. There is a ball bearing which I have but then there are two needle bearings on the ID of the spur gear. Those two needle bearings are the ones I'm talking about.